Trad Talk Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-18 of 22 Results
  1. TradTalk Main Forum
    I have a DAS Tribute, but it is too heavy for my bum shoulder. I looked in the documentation for the tribute to see how I can remove the riser weights (for now). I have it for sale, but I would like to keep it. Eventually my shoulder will get stronger. How do you remove the riser weights on a...
  2. TradTalk Main Forum
    I have a little issue, I have limb savers on my hexx 7 limbs that i put on about a year ago. I just bought a slide on selway quiver that i want to put on these limbs, anybody have any luck removing the limb savers without damaging the limb finish, any tips or tricks thanks brad
  3. TradTalk Main Forum
    The other Bear MAg thread got me thinking. I have a B mag that has a broken screw on the sight plate. The screw is tiny 4-40 or 6-32. ANy tricks to remove it Also one of the latches has a mis-matched screw. I would like to replace that one too any idea of a source. While I am asking...
  4. TradTalk Main Forum
    I have a Hoyt Spectra riser that has been painted with a Krylon paint. I want to remove it before sending it to Johndo to be warfed. Have any of you done this, and if so, what removal technique did you use. I know there are chemical strippers available but I am not sure what effect they may...
  5. TradTalk Main Forum
    I got some FMJ with the HIT inserts that was set for a compound; what is the best method of removal the inserts without damaging the FMJ. I need to do some trimming for bareshafting, they are currently cut to 30" and my draw is 27.5". Any info would be greatly appreciated. Good Hunting-JJ
  6. TradTalk Main Forum
    I'm possibly getting back a riser that was powdercoted. New owner did not sand it, but simply painted over it. What are the odds I can remove the paint and not damage the powdercote? What products & methods would you use? Thanks in advance.
  7. TradTalk Main Forum
    How are these nock inserts removed? Please don't say with great difficulty!
  8. TradTalk Main Forum
    I picked up 3 recurves from a estate this week, after close inspection 2 are bear grizzly's from the 60's the third wasn't recognizable. someone covered them in duck tape from tip to tip and many years later peeled it off. I am left with the dry duct tape residue. I tried many solutions wd40...
  9. TradTalk Main Forum
    Please, take off the Chevrolet add as it comes up on every page unless I am logged in. For various reasons I am not always logged in when viewing. tks Dennis
  10. Bow Projects
    I have a set of KAP carbon Challenger limbs with a (non-ILF) locator button where the ILF fittings would be. This is just a springloaded button with a metal housing. How can I remove this? Thanks
  11. Watering Hole
    Sure beats the hell out of that old door knob trick in coolness factor. Pretty gutsy of this young lady to "give it a shot" . Neat idea...
  12. TradTalk Main Forum
    Hey folks. I've been shooting a little bit and the velcro rest on my shelf is getting a little worse for weat and I'd like to strip it off and put some leather on there. Any ideas on how to get it off without damaging the wood? Thanks!
  13. TradTalk Main Forum
    What's a good solvent for removing Fletchtite from a carbon shaft? I normally just scrape it off, but on these Beman Classics I have, the glue doesn't want to come off for anything.
  14. Bow Projects
    Well, I just removed the skins from my winex limbs. I did a little searching and saw a few different methods suggested and went for it. I carefully peeled them off leaving them intact. Next, I put them in very warm water and let them soak for about a half hour to soften the glue. I used...
  15. TradTalk Main Forum
    I am gearing up to Warf a Proline Condor riser. There is a hump where the limb bolt goes through the riser. I want to grind the hump down to get the limp pocket level. There is a helicoil in the hole. Can they be salvaged? If so, do I need a special tool? Is it worth the effort to salvage...
  16. TradTalk Main Forum
    Slowly but surely I'm getting my "Xmas to me" list made with the help of this forum. I know I'm asking a lot of questions and really hope it's not bothering anyone by the constant asking for help and opinions. Has anyone tried the Bohning feather stripper called "The Stripper" (can't fault the...
  17. TradTalk Main Forum
    I am wanting to paint a few of my warf risers and was wanting to know if there is a easy way to remove the grip do they snap on or ??? Thanks
  18. TradTalk Main Forum
    Just DAS-playing with a couple new-to-me sets of Hoyt limbs, Vector mediums and a set of FX longs. the Vector ILFs came out with no problem, an allen wrench disassembled them and they punched out as usual. My problem is the ILF on the FXs looks like it requires a special spanner to remove...
1-18 of 22 Results
Top