Search Results for ‘insert’

Quick guide on how to reinforce your axis arrow and get the most durable set up possible. You will be able to insert tune with this method. Requires an ironwill impact collar and some know how. But just take a look and consider the information. If you find it relevant to your arrow build I hope...

I have a dozen uncut .231 adjustable static inserts from Ethics Archery for sale (no trades). These weigh 175 grains full length and they can be cut down to 50 grains. The lip opens outward and takes 5/16" field points. Two were glued in with low temp hot melt and shot a few times while the...

Anyone know the length of the Vforce RPS insert? Looks about double the length of a standard insert. I'm wondering if having an insert this long affects the spine like in the Victory VAPs with having a long shank in the field points. Making the arrow stiffer thus I can shoot a heavier tip...

Anyone know where I can get 100gr inserts for 1916 aluminum arrows?

Dear Memebers, Unfortunately on the CarbonExpress Homepage do not exist insert for screw in point for Maxima Pro Recurve RZ shafts... The ID of this shaft is .234"... I am looking for insert, which fit into this shaft. Could someone help me? What insert fit into the 420 CE Maxima Pro RZ ...

Just acquired a rather rough Black Bear riser and the stabilizer insert is missing. I would like to replace it or maybe just fill the hole up with something decent looking. Any ideas? Thanks

I built myself a new backstop last week using a rubber horse stall mat. I works great for stopping arrows. Often they bounce off and they penetrate they only make it 5 or 6 inches in. But when I pull the arrows out often the inserts are catching and pulling loose from the arrow. So far...

Put some inserts in last night, and did my usual fine job of getting my fingers covered in goo. Problem is this time I used AAE Max Impact Insert Glue, so it looks like I was putting tar on my roof or something. I tried everything to clean up my hands when finished, but my hands are still dark...

I got some Victory VAP arrows, used.....some V1s and V3s.....all .500s. What are you guys using for inserts, and were do you get 'em? Anyone got any extra inserts?

I want to try the Beiter insert nocks on aluminums with uni-bushings. I like the 3D supernocks but they are helpless when I try stringwalking. I could try bigger serving, but that might not cut it.. Do you like the insert nocks that fit the bushing, or is it better to cut the uni bushing off...

How are these nock inserts removed? Please don't say with great difficulty!

I'm trying to find a arrow insert with .220" diameter. I think one of the ACC might work. Can someone give me a name for an insert with that dimension. Thanks Bob

I've read on here a few times people are using gorilla glue? I don't remember the thread if it's for fletching or inserts? Or I would do a search and reaserch it. Got me to wondering the gorilla glue I have is an expanding type, I would think for inserts it would push them out? If people do...

I have looked at quite a few threads on this and still have one question. In one of Roger's threads he said he put a rubber pad under the limb. I now have a set of limbs with the inserts and it looks like a pad 1/8" thick with a 3/8 hole will do the trick. My question is this right and is there...

I know I will get the right answer here... what insert, ACC or what has a inside diameter od .215+-???????? Thanks. Bob

I will be installing HIT inserts on new Beman MFX shafts, and I've read that this can be done effectively using hot melt glue instead of epoxy, allowing easier removal of the insert if necessary. My other concern is aligning my broadheads - should I forget using the little green tool in favor of...

I went to a shoot over the weekend and had several inserts pull out. I called the shop and they said they recently switched to insert iron. They used two part in the past. Any ome else losing inserts with this stuff? Lou

Where would you get a metal plunger insert if you wanted to drill and tap an actionwood riser for using a plunger? Did an internet search but came up with nothing as well as checking 3 Rivers and Lancaster. Thanks! Greg

OK, been making my own arrows for 36 years now. I started out with aluminum went to wood and now shoot mostly carbon. I have tried just about everything and still having some trouble with inserts coming out. I do the cleaning with alcohol, roughed them up a bit the whole sha-bang but again most...

Anyone know what the metric size is for these? The chart I found suggests M5-.08......whatever that is....sound right? I might just re-tap them to something all the quiver manufacturers supply with their quivers. Thanks for any help. -Rob