Search Results for ‘bolts’

Anyone know max # of turns out on limb bolts? Black Bear with plates using Trad Tech med limbs. Don't remember what the bolt length is, but from cranked down to all the way out is 16 turns. TIA.

Anyone on here make custom antler bur limb bolts with designs on them? I'm not really interested in doing them myself and have seen folks offer them for sale years ago on here. Longest I've seen sold by companies is 2" and I would need them 2-1/4" inches with full threads for my particular...

Most conventional limb bolts are 5/16'sx18 threads. I have personally never had the walk lose when shooting. What I do is: Wrap Plumbers Teflon tape around the threads three turns and install them back into the threads. This has worked well for me on Warf Risers and actually see no need to...

Hi all, I’m new to metal risers, and my translation of Italian translations is not so perfect... I want to match some arrows to my limbs and it looks like it will take it to the lighter end of the adjustments (screwing out bolt). Does anyone understand what their recommendation for how far...

I have found that Teflon plumbers tape works well to hold adjustment on ILF limbs not on just my Warf risers but also on any riser. I wrap the bottom of the bolt starting the tape on the bottom (if held with the bolt upside down) clockwise orientation to keep it from binding on the threads and...

I'm considering moving in the limb bolts when I warf my Proline. For those that have done this, is it also necessary to shorten the limb pocket at all? It seems the proline limb pockets are generously long to begin with.

Two years ago I bought a Hoyt Dorado riser with the intention of having an ILF conversion done. I decided to go with the the bolt down ILF limbs instead. I was thinking ILF again when a question came up that I didn't think of before and I don't recall seeing it addressed. How are the tiller...

Hi are limb bolts the same thread size on all bows ? as id like a pair of antler limb bolts for my dorado ? cheers Dan

Hello, I'm searching a Riser. Loc did a superb job in converting a Bear Mini Magnum for me. But from the very beginning I was interested in a riser with the bolts preinstalled. Does anyone have one for Sale/Trade? regards stroey

Folks?...there's been much angst on the net regarding the 25" Hoyt Horizon ILF Riser's "Limb Bolt Adjustment"...mainly problems with folks not being able to get a proper sized hex key to fit and and tighten (or loosen) the Limb Bolt SET Screw well?...the hex key size is a ridiculously small...

I'm back to playing around with ILF again and see that Hoyt has some limb bolts with a head that pivots to keep aligned with the face of the limb. That's one thing I never liked about standard ILF limb bolts, just having minimal contact at certain load settings. It would seem like the pro bolts...

Hi all my name is Pete, from CT. I am here daily but I don't post much. I have a question for the DAS gurus. I have my bolts on my 17" DAS turned all the way in, but I recently got a set of hex 5s from Sid for my 11 yr old nephews DAS set up. He also has a 17" riser(my loaner). At his 25"...

New Blacktail limb bolts for the Snakebit. Amazing detail and craftsmanship, the kind getting harder and harder to find. You can see the hand engraving up close. No, I really didn't "need" them, but they were too nice to pass up. Sorry for the bad lighting, any discoloration is due to the...

Are there any ILF riser bolts out there that are longer than the norm? If so does anyone know where to get them? Context is that one of my limb sets comes in a lot heavier in sub-zero temps & I'm a little concerned about going out over 5 turns on the current bolts. Thx for your assorted...

Anybody know who makes custom carved limb bolts? Open to ideas on material too. Steve